♦ USB Power
No special battery required. Use USB power supply (5V • 2A).
The heating vest can be charged by the portable rechargeable battery pack of a bicycle, USB power from a car or portable mobile power unit. It is convenient to use for outings or at home.
♦ Kimono Vest
Family Size: from S size to XL size. It is suitable for wearing the Kimono vest in all these sizes.
Add Velcro, imitation kimono feeling.
|
Size
|
Shoulder
Width
|
Clothing Width |
Clothes Length |
|
Largest
|
300 |
500 |
630 |
|
Smallest
|
500 |
600 |
630 |
♦ LED Illuminated Switch
LED illuminated switch and corresponding heater set point.
Choose the temperature according to the situation - push the switch to show red, white or blue light. Installed under the front pocket, combined with the hand warmer. The heating point is divided into three locations.
1.Introductions of Electronic Temperature Adjuster
|
The electronic temperature regulator has five modes of power output including preheat,
high, medium, low and off.Each mode is based on power as follows:
|
|
1 |
(Preheat),98% power output |
|
2 |
(HIGH),85% power output |
|
3 |
(MEDIUM),60% power output |
|
4 |
(LOW),30% power output |
|
5 |
(Off),No power output |
2. Photos of Electronic Temperature Adjuster
|
1.Front View of Product |
2.Reverse Side of Product |
|
|
 |
|
3.Preheat Position
(LED light illuminates red.)
|
4.High Temperature Position
(LED light illuminates red.)
|
|
|
 |
|
5.Medium Temperature Position
(LED light illuminates white.)
|
6.Low Temperature Position
(LED light illuminates blue.)
|
|
|
 |
3.Introductions of Electronic Temperature Adjuster
|
Wiring Methods of Electronic Temperature Adjuster |
|
1.
|
The electronic temperature adjuster has 3 wires at the output, white, red and blue respectively. |
|
2.
|
White wire |
Negative input, connecting to the negative terminal of the battery. |
|
3.
|
Red wire |
Positive common wire at the input and output, connecting the positive and negative heating pads. |
|
4.
|
Blue wire |
Negative output, connecting the heating pad as a negative load. |
|
The switch connects the input to battery and the output to the heating pad.
|
|
Sequenc No. |
Position |
Output |
Operating Instructions |
Status Display
|
|
2 |
first position(high temperature)
|
85% |
To turn on, press the switch key for 2〜3 seconds. |
Enter the preheat state:
98% power output, 5 minutes timing to preheat, automatically entering the high temperature position after 5 minutes; LED light illuminates red. |
|
3 |
second position(middle temperature)
|
60% |
Press the switch key again. |
Enter the medium temperature position will change the LED light to white. |
|
4 |
third position(low temperature)
|
30% |
Press the switch key again. |
Enter the low temperature position will change the LED light to blue. |
|
5 |
repeat operation |
Press the switch key again. |
Enter the high, medium or low position.Loop according to this sequence, which shou ld illuminate the corresponding LED indicator light.
|
|
6 |
closed position |
Press the switch key for 2〜3 seconds and the device enters the preheat position. |
Whatever state the system is currently located in, it will enter the closed state by long pressing the switch key.The LED indicator light gradually turns off without power output.
|
4.Related Parameters of Electronic Temperature Adjuster
|
Sequence No. |
Item |
Detailed Parameters |
|
1 |
Work Voltage (V)
|
5.5V - 9V |
|
2 |
Work Current (A)
|
≤2A |
|
3 |
Product Specification (mm)
|
H: 7mm*W:34mm*L:34mm |
|
4 |
Product Weight (g)
|
6g |
|
5 |
Specification Used for LED Light
|
in single red, white and blue color |
|
6 |
Work Temperature Range
|
-40～+85℃ |
|
7 |
Stored Temperature Range
|
-40～+85℃ |
5.Warning and cautions:
The product should be stored in a cool, dry environment. Do not store near high temperatures such as a heater or fire. Do not strike, trample or throw. Do not reverse the positive and negative electrical connections.
|
